To menu
D-Top3:
D-Top3 has been designed for a vertical coverage of 8 degrees, and a horizontal coverage of 90 degrees, excellent properties for PA-applications for an audience up to about 300 persons within approximately 15x15m floor space.
The sub to be used in conjunction is the D-Sub1 (1,5kW 18inch).
The D-Top3 also makes an excellent in-fill or delay-top for the bigger events using one or two pcs. D-Top1 each side. Additionally, in full range mode, the D-Top3 is very well suited as stand-alone PA for applications with less bass demands.
Two D-Top3 tops can be flown or stacked on top of each other, high sections together, resulting in good acoustic coupling even in the high frequencies. In this way, the acoustic coupling boosts the SPL up to 139 dB full space, with the same horizontal coverage and good vertical beaming, with neglectable phase funnies and lobing.
When conventional side-by-side stacking is preferred, horizontal coverage can be increased to 180 degrees. Allthough the acoustic coupling will not be perfect for the entire frequency range, this stack will yield up to 6dB gain for the low mid regions, down to 3dB gain for the high frequency regions.
This top uses two high efficiency (97dB/1w/1m) 10 inch neodymium mid speakers in a reflex enclosure. Average sensitivity is better than 100dB/1w/1m full space.
A state of the art switching amplifier delivers 800 watts of cold power into the mid section, and 120 watts into the high section. These amplifiers use switched power supply for best mains efficiency and weight benefits. Newly developed smart processing ensures safe operating conditions for all drivers. Additionally, level dependant Fletcher Munson Compensation processing is performed to achieve best performance at all sound levels.
To menu
D-Top3:
Very high output
Incorporated digital amplifiers
Superior signal processing including Fletcher Munson implementation:
Best soundquality at every sound level
Practical 90 degrees horizontal coverage
Narrow vertical beam: Less feedback risc
Less floor- and ceiling reflections:
Soundquality is less compromized by room acoustics
Increased authority, highly improved intelligibiliy at greater distances
Much better projection compared to conventional systems particularly in difficult acoustic environments!
Superior coupling amongst two D-Top3, high sections forming a bigger line array, yielding even better long throw properties.
Compact size
Low weight
|
|
Concept Mid High Frequency range Amplifier Max SPL @ 1m Coverage Dimensions Weight Optional flying hardware |
|
active high output top dual 10 inch Planar Wave horn 100Hz-18kHz top mode (fullrange: 60 Hz-18kHz) digital, 800W mid, 120W high, processor controlled, including FMC-implementation 128dB full space (Calculated and confirmed in real life measurement using a pink noise burst) 90' horizontal, 8' vertical HxWxD=73x33x27cm 23Kg External brackets using 4x M10, designed for flying one or two tops. |
D-Top3 has been designed for a vertical coverage of 8 degrees, and a horizontal coverage of 90 degrees, excellent properties for PA-applications for an audience up to about 300 persons within approximately 15x15m floor space.
The sub to be used in conjunction is the D-Sub1 (1,5kW 18inch).
The D-Top3 also makes an excellent in-fill or delay-top for the bigger events using one or two pcs. D-Top1 each side. Additionally, in full range mode, the D-Top3 is very well suited as stand-alone PA for applications with less bass demands.
Two D-Top3 tops can be flown or stacked on top of each other, high sections together, resulting in good acoustic coupling even in the high frequencies. In this way, the acoustic coupling boosts the SPL up to 139 dB full space, with the same horizontal coverage and good vertical beaming, with neglectable phase funnies and lobing.
When conventional side-by-side stacking is preferred, horizontal coverage can be increased to 180 degrees. Allthough the acoustic coupling will not be perfect for the entire frequency range, this stack will yield up to 6dB gain for the low mid regions, down to 3dB gain for the high frequency regions.
This top uses two high efficiency (97dB/1w/1m) 10 inch neodymium mid speakers in a reflex enclosure. Average sensitivity is better than 100dB/1w/1m full space.
A state of the art switching amplifier delivers 800 watts of cold power into the mid section, and 120 watts into the high section. These amplifiers use switched power supply for best mains efficiency and weight benefits. Newly developed smart processing ensures safe operating conditions for all drivers. Additionally, level dependant Fletcher Munson Compensation processing is performed to achieve best performance at all sound levels.
To menu